The incoming test of green laser pointer has to be done

The incoming test of   green laser pointer  has to be done. Laser cutting laser cutting technology is widely used in metal and non-metallic materials, processing, can significantly reduce processing time, reduce processing costs, improve quality of the workpiece. Laser cutting technology, there are two: one is the pulsed laser for metal materials. The second is a continuous laser for non-metallic materials, which is an important application of laser cutting technology field. The laser has become one of modern fantasy pursuit of "cut iron drunk" and "sword." Focusing mirror is focused on the CO2 laser beam melts the material surface, while with the laser beam with the compressed gas is blown away by the molten material and the laser beam and the material for the relative motion along a certain path, to form a certain shape the kerf. The process engineer has submitted the suggestion of the workers about the technical problems of   green laser pointer   to Chief Engineer.
Since the 1970s from a CO2 laser and CNC technology with the continuous improvement and development, industrial sheet metal cutting has become an advanced processing methods. In the fifties and sixties as a cutting board cut the main method: For the use of oxyacetylene flame cutting plate; for the use of scissors under the bed sheet material, forming large quantities of complex parts using stamping, cutting a single piece of vibrating. Seventies, in order to improve and enhance the quality of flame cutting incision, but also to promote the ethylene oxide precision flame cutting and plasma cutting. In order to reduce the manufacturing cycle of large stamping dies, but also the development of CNC and EDM technology nibbling. Material under a variety of cutting methods has its shortcomings, in industrial production in a certain scope. Laser cutting machine equipment, tens of thousands or even tens of ten thousand pieces, so care must be taken of them in operation, and usually pay attention to maintenance and repair in order to increase equipment life, cost savings, and create greater benefits. The factory has got more market share recently for the low price and high quality of   green laser pointer   .
Recommendation: weekly cleaning and replacement of the circulating water tank once. Note: the machine before work to ensure that the laser tube filled with circulating water. Circulating water temperature directly affects the water quality and the service life of laser tube, it is recommended to use purified water, and temperature controlled at 35 ℃ or less. If more than 35 ℃ in need of replacement cycle of water, or add ice water down to the water, (recommended user to select the cooling machine, or use two tanks). Clean the water tank: First turn off and unplug the water saliva control, so that the laser tube of water flow automatically into the tank, open tank, remove the pump to remove water pump on the dirt. Clean the tank, replace the vicious cycle of water, the pump reverts back to the tank, the pipes will connect into the pump inlet, collated the joints. Separate the pump power, and run 2-3 minutes (the laser tube filled with recycled water). The use of fans for a long time, will accumulate a lot of fans inside the solid dust, so fans have a great noise, not conducive to the discharge and odor. The customer has the stricter requirements for quality of      usa green laser pointer .
When the exhaust fan suction less than poor, first turn off the power, the fan on the pipe and out into the air duct removed, remove the dust inside, and then the fan upside down, and pull the fan moving inside, clean up , then the fan installed. Engraving machine has three mirrors and a focusing mirror (mirror 1 launch at the exit of the laser tube, which is the upper left corner of the machine, No. 2 in the beam of the left mirror, mirror 3, the fixed part in the laser head the top of the focusing mirror in the laser tube in the lower adjustable), the laser is reflected through these lenses, focused emitted from the laser head. Lens easily coated with dust or other contaminants, resulting in the loss or the laser lens is damaged, 1 and 2, the lens cleaning Needless to remove, simply wipe moistened with lens cleaning fluid lens paper carefully along the central to the edge of the rotary cleaning. 3 lenses and focusing mirrors need to remove from the frame, using the same method to wipe, wipe the back can be installed after the AS. Chief Engineer hosted the meeting during which some technical details of   green laser pointer   had been determined.